P0014 Toyota Sequoia Code: Camshaft Position Timing Over-Advanced or System Performance Bank 1

Toyota’s OBD-II trouble code P0014 is the Camshaft Position “B”, which indicates Timing Over-Advanced (Bank 1) or System Performance. This means that the exhaust camshaft on cylinder one is too advanced.

In this article, I will be talking about the P0014 trouble code in Toyota, its symptoms, causes, and how to fix it.

P0014 Toyota Sequoia Trouble Code Definition

P0014 trouble code in Toyota is defined as Camshaft Position Sensor B Timing Over-Advanced or System Performance (Bank 1).

What Does The P0014 Code Mean In Toyota Sequoia?

Toyota’s P0014 trouble code is an internal code that indicates excessive camshaft position (CMP) timing is in advance of what the ECU ordered it.

This code can be found alongside P0011, P0012, or P0013.

The trouble code P0014

Bank 1 is the area in the engine that houses the first cylinder. Position “B” refers to an exhaust camshaft. This can, depending on the vehicle make/model, be located either at the rear or right from the driver’s perspective.

The P0014 trouble code indicates the camshaft has been over-advancing. This means it is exceeding a threshold set forth by the Engine Control Module. It may be advancing or slowing down its timing.

Toyota Sequoia P0014 Code Possible Causes

Toyota’s P0014 trouble code is generated when the vehicle’s computer detects an over-advancing exhaust camshaft on bank 1.

The check engine light will be illuminated to notify drivers, and the ECU will save a P0014 code.

Toyota Sequoia P0014 code could be triggered by several things:

• Improper Camshaft Timing
• Defective Camshaft Timing Control Solenoid
• Variable camshaft tuning (VVT), or variable valve timing (VCT), fails
• The oil lines for the variable camshaft timing (VVT), or variable camshaft tuning solenoid (VCT), become clogged with debris.
• Low Engine Oil
• Low Oil Pressure
• Defective Camshaft Position Sensor
• A neglected crankshaft position sensor
• Wiring that is damaged
• Defective timing belt or timing chain
• Defective Timing Tensioner

Toyota Sequoia P0014 Code Common Symptoms

• The Check Engine Light will illuminate, indicating an issue.
• Problems with the camshaft could cause this to occur. Listen to the clicking sound as the car starts or stops while you turn the key. The car will not start if you don’t fix this.
• Stalling: Your vehicle might experience similar issues to problems starting.
• P0014 Code May Cause Significant Decreasing Fuel Economy. It is possible for the P0014 code to cause a sudden decrease in fuel economy. This makes it easier to identify.
• Noise and vibration from the Engine: An incorrect fuel-air mixture can lead to a rough ride. Your vehicle may shake, emit more exhaust smoke, or run louder than usual.
• Engine emissions can cause vehicles to fail emission tests.

Is It Safe To Drive a Toyota Sequoia With a P0014 Code?

It is not safe to drive a Toyota equipped with the P0014 trouble code. An issue with the timing of camshafts could lead to engine failure. In this case, it can be costly and time-consuming to replace the engine.

Many people become worried when their vehicle won’t turn on or isn’t responding to their commands. However, the extent of the problem will depend on the cause.

Engine damage will occur if the timing chains aren’t working properly. Failure to bring your vehicle in for repairs can lead to additional damage and a high repair bill. It is important to contact a mechanic immediately to diagnose the problem and get it fixed.

Toyota Sequoia P0014 Code: How To Diagnose

Without the right knowledge and experience, diagnosing a Toyota P0014 code can be difficult.

It can be difficult to achieve camshaft timing due to the complexity of some systems.

Most people can quickly identify the trouble code P0014 with some basic knowledge.

1. Use an OBD2 scanner to search for trouble codes that might be causing the P0014 error. You should look for any trouble codes that are related to the crankshaft position sensor and camshaft position sensors to resolve the P0014 code.
2. To ensure that your engine oil is sufficient, check the level. Add oil to your engine oil level or replace the filter. Clear out any P0014 error codes, and then try again.
3. To check for sludge in the engine, take a look at your service manual and oil cap. You may have engine oil that is very old. This could be clogging the oil lines to the variable valve timing or variable camshaft tuning engine control valve. It may be necessary to change both types of oil and clean both components.
4. Your diagnostic scanner can test the variable valve timing (VVT
5. Remove the variable camshaft tuning control valve solenoid (VCT) and clean the oil passages with compressed air and a suitable cleaning agent.
6. To confirm that they send accurate signals, verify the position sensors on the crankshaft and camshaft.
7. You can manually check the timing of your engine’s camshaft. Refer to your owner’s guide for details on how to do this in your engine. If the timing chain or timing belt is damaged, take it apart and inspect it for any damage.

Toyota Sequoia P0014 Code: Common Diagnosing Mistakes

A common misdiagnosis in Toyota Sequoia’s P0014 code is to mistakenly believe that the timing belt or chain is defective.

Replacing a damaged device can be costly. In many cases, other issues could cause the P0014 code to appear. It is important to conduct a thorough diagnosis before you begin repairs.

Toyota‘s P0114 code indicates a malfunctioning VVT/VCT system that regulates camshaft timing. Other possible causes include an incorrect camshaft position sensor or low oil levels.

How Much Does It Cost To Repair P0014 Code In Toyota Sequoia

Repairing the P0014 code on Toyota Sequoia costs $220 in total. The parts cost $160 while labor costs $60.

What Repairs Can Fix The P0014 Code in Toyota Sequoia?

• Change the oil filter and add or remove engine oil.
• Clean the oil lines for variable camshaft tuning (VCT), or variable valve timing(VVT) systems.
• Replace or clean the variable camshaft tuning solenoid (VCT), or variable valve timing solenoid (VVT).
• Replacing the timing chain or belt
• Replacing the solenoid of the camshaft timing control valve
• Adjusting the camshaft position sensor
• Replace the crankshaft position sensor
• Repair any defective wiring

How To Fix The P0014 Code In Toyota Sequoia

• Clearing error codes, and performing a road-test
• You can extend the engine’s life by changing the oil filter and oil with engine-specific viscosity oils.
• Replace or repair the wiring for the bank 1 exhaust camshaft oil valve.
• Bank 1 needs to replace its exhaust camshaft oil control valve.
• When replacing or fixing the timing chain, camshaft-phasers, and/or camshaft-phasers, please refer to the service manual.

In Conclusion

Toyota’s P0014 code indicates that there is a timing problem with the camshaft. The problem could be due to improper timing of the camshaft. You need to fix this immediately or you will get a high repair bill.

It can also be caused simply by the insufficient engine oil, or malfunctioning camshaft position sensors – both of these are typically repairable for less than $200.

You can contact a qualified mechanic right away if you are unsure of your ability to solve the problem.