OBD-II code P0014 in Toyota Etios means Camshaft Position “B” – Timing Out of Balance or System Performance (Bank 1). This indicates that the exhaust camshaft is not working properly.
In this article, I will be talking about the P0014 trouble code in Toyota Etios, its symptoms, causes, and how to fix it.
- P0014 Toyota Etios Trouble Code Definition
- What Does The P0014 Code Mean In Toyota Etios?
- Toyota Etios P0014 Code Possible Causes
- Toyota Etios P0014 Code Common Symptoms
- Is It Safe To Drive a Toyota Etios With a P0014 Code?
- Toyota Etios P0014 Code: How To Diagnose
- Toyota Etios P0014 Code: Common Diagnosing Mistakes
- How Much Does It Cost To Repair P0014 Code In Toyota Etios
- What Repairs Can Fix The P0014 Code in Toyota Etios?
- How To Fix The P0014 Code In Toyota Etios
- In Conclusion
P0014 Toyota Etios Trouble Code Definition
P0014 trouble code in Toyota Etios is defined as Camshaft Position Sensor B Timing Over-Advanced or System Performance (Bank 1).
What Does The P0014 Code Mean In Toyota Etios?
Trouble code P0014 in Toyota Etios signals that the camshaft is positioned in advance on bank 1.
It can be viewed alongside other codes, such as P0011, or P0012, but not P0013.
The trouble code P0014
indicates the exact location of the error.
Bank 1 refers to the engine region that contains the first of the cylinders. Position “B”, or an exhaust camshaft, is a position in which the engine has the first cylinder.
Depending on your vehicle’s make/model, it may be at the right side or the rear depending on the perspective of a driver.
The P0014 trouble code indicates a camshaft that is excessively advanced. This means the engine control module (ECM), has set a threshold that will allow it to advance or retard its timing.
Toyota Etios P0014 Code Possible Causes
Toyota Etios’s P0014 trouble code is generated when the vehicle’s computers detect that the exhaust camshaft at bank 1 is too advanced or ahead of schedule.
As a result, the check engine lamp will light up to warn drivers. Additionally, the ECU will store a code called P0014.
Toyota Etios’s P0014 codes can be triggered by many things.
- Improper Camshaft Timing
- Defective Camshaft Timing Control Solenoid
- Failed variable camshaft tuning, (VVT), and variable valve timings (VCT).
- Oil lines for variable camshaft tune (VCT) and variable valve timing (VVT
) solenoids can get clogged up with debris. - Low Oil Levels
- Oil Pressure Low
- Defective Camshaft Position Sensor
- A neglected crankshaft position sensor
- Infected wiring
- Defective timing chain/timing belt
- Defective Timing Tensioner
Toyota Etios P0014 Code Common Symptoms
- The Check Engine Light flashes to indicate an issue.
- The problem could be caused by camshaft problems. When you turn the key, listen to clicking sounds that indicate the car is starting and stopping. If it doesn’t resolve, it might not start at all.
- Stalling is a similar issue to problems with starting. Your vehicle could experience difficulty idling at low speeds or even stall out completely.
- P0014 Code Can Cause Significant Decreasing Fuel Economy. The P0014 code could cause abrupt drops in fuel economy. This makes it easier to identify.
- Noise and vibration coming from the engine: A camshaft problem can lead to rough riding due to an insufficient fuel-air ratio. Your vehicle could be shaking or emitting more exhaust fumes than usual.
- Due to engine emissions, vehicles will fail emission testing.
Is It Safe To Drive a Toyota Etios With a P0014 Code?
It is not safe to drive a Toyota Etios with the P0014 trouble code. An issue with the timing of camshafts could lead to engine failure. In this case, it can be costly and time-consuming to replace the engine.
Many people become worried when their vehicle won’t turn on or isn’t responding to their commands. However, the extent of the problem will depend on the cause.
Engine damage can be caused by timing chains that aren’t working properly. Failure to bring your vehicle in for repairs can lead to additional damage and a high repair bill. It is important to contact a mechanic immediately to diagnose the problem and get it fixed.
Toyota Etios P0014 Code: How To Diagnose
It can be challenging to diagnose a Toyota Etios P0014 problem code without having the right insight and expertise.
Camshaft timing can be complicated due to the complexity and variety of systems. Without the appropriate tools and knowledge, it might prove difficult.
The P0014 trouble code can be quickly diagnosed by anyone with basic computer knowledge.
- Connect an OBD2 scan tool and look for any trouble codes causing the code P0014. To resolve your P0014 error, you should first diagnose the crankshaft positioning sensor or camshaft location sensor.
- Check the engine oil level to ensure it is in good condition. If the level is too low, you can add oil or change both the oil-filter combination. Clear out P0014 error codes.
- For signs of sludge, check your oil filler cap as well as the service manual. Your engine oil could be very old, clogging its oil lines to either the variable valve tuning (VVT) or variable camshaft tun (VCT), engine control valves. In these cases, you may need to change both the oil type and clean both parts.
- Your diagnostic scanner will allow you to check the variable valve timing or variable camshaft tun (VCT), solenoid. Do an output test to check if the VCT-valve solenoid moves. Use 12v+ power and ground to experiment with your car’s electrical system.
- If possible, remove the variable camshaft tun (VCT), and solenoid control valve and clean oil passages with compressed and suitable cleaning solutions.
- Verify that crankshaft and camshaft position sensors send the correct signals.
- You can manually verify the timing of the engine camshaft by consulting your manual. If your timing belt or chain is worn, you can disassemble it and inspect the damage.
Toyota Etios P0014 Code: Common Diagnosing Mistakes
A common misdiagnosis in Toyota Etios’s P0014 code is to mistakenly believe that the timing belt or chain is defective.
Replacing a damaged device can be costly. In many cases, other issues could cause the P0014 code to appear. It is important to conduct a thorough diagnosis before you begin repairs.
Toyota‘s P0114 code indicates a malfunctioning VVT/VCT system that regulates camshaft timing. Other possible causes include an incorrect camshaft position sensor or low oil levels.
How Much Does It Cost To Repair P0014 Code In Toyota Etios
Repairing the P0014 code in Toyota Etios costs $140. The part costs $60 while labor costs $80.
What Repairs Can Fix The P0014 Code in Toyota Etios?
- Remove excess oil and change your oil filter.
- Cleaning the oil lines of variable camshaft tune (VCT), and variable valve timing system (VVT).
- Clean or replace the variable camshaft tune (VCT), variable valve timing, (VVT), and solenoid.
- The timing belt or chain can be replaced
- Replace the solenoid in the camshaft timing controller valve
- Adjust the Camshaft Position Sensor
- Replace the sensor for a crankshaft position
- Repair any damaged wiring
How To Fix The P0014 Code In Toyota Etios
- Clearing error codes, and performing a road-test
- You can extend the engine’s life by changing the oil filter and oil with engine-specific viscosity oils.
- Replace or repair the wiring for the bank 1 exhaust camshaft oil valve.
- Bank 1 needs to replace its exhaust camshaft oil control valve.
- When replacing or fixing the timing chain, and camshaft-phasers, or replacing them, please refer to the service manual.
In Conclusion
Toyota Etios’s P0014 codes indicate a timing issue with your camshaft. The cause for this is incorrect camshaft timing. You will need to fix this immediately.
But it can also happen due to insufficient engine oils or malfunctioning camshaft positioning sensors. Both are easy to fix and cost less than $200.
If you are not sure that you can fix the problem, consult a mechanic.
