P0014 Toyota C-HR Code: Camshaft Position Timing Over-Advanced or System Performance Bank 1

OBD-II Trouble Code P0014 in Toyota C-HR indicates Camshaft Position B – Timing over-Advanced or Performance (Bank 1), which means the exhaust camshaft of the first cylinder may be too advanced.

In this article, I will be talking about the P0014 trouble code in Toyota C-HR, its symptoms, causes, and how to fix it.

P0014 Toyota C-HR Trouble Code Definition

P0014 trouble code in Toyota C-HR is defined as Camshaft Position Sensor B Timing Over-Advanced or System Performance (Bank 1).

What Does The P0014 Code Mean In Toyota C-HR?

P0014 in Toyota C-HR means that the camshaft position on cylinder one (bank 1) is over-advancing (ahead of time).

You may see it alongside related codes like P0011, and P0012.

The location of the error is indicated by the trouble code P0014.

Bank 1 refers to the engine region that contains the first of the cylinders. Position “B”, which is an exhaust camshaft, can be found depending on vehicle make/model at either the rear or right side, from a driver’s standpoint.

The P0014 trouble code indicates that the camshaft is too advanced. This means that it exceeds a threshold set in the Engine Control Module (ECM), while either advancing its timing or retarding it.

Toyota C-HR P0014 Code Possible Causes

Toyota C-HR generates the P0014 trouble codes when it detects that the exhaust camshaft bank 1 is either over-advancing or ahead of schedule.

A check engine light will go on to alert drivers. The ECU will also store the P0014 code.

Possible causes for P0014 in Toyota C-HR include:

• Improper Camshaft Timing
• Defective Camshaft Timing Control Solenoid
• Failed variable camshaft tuning or variable valve timing
• Oil lines for variable camshaft tuning or variable valve Timing (VVT) solenoids can become clogged.
• Low Oil Levels
• Oil Pressure Low
• Defective Camshaft Position Sensor
• A neglected crankshaft position sensor
• Broken wiring
• Defective timing chains or timing belts
• Defective Timing Tensioner

Toyota C-HR P0014 Code Common Symptoms

• The Check Engine Light flashes to indicate an issue.
• The problem could be caused by camshaft problems. When you turn the key, listen to clicking sounds that indicate the car is starting and stopping. If it doesn’t resolve, the car might not start at first.
• Stalling is a similar issue to problems with starting. Your vehicle could experience difficulty idling at low speeds or even stall out completely.
• The P0014 code causes significant fuel economy declines: It may be difficult to detect because it can cause sudden drops in fuel economy.
• Vibration and noise from the engine: A bad fuel-air ratio can cause rough riding. The vehicle might shake more than usual, emit more exhaust fumes, or be louder.
• Due to engine emissions, vehicles will fail emission testing.

Is It Safe To Drive a Toyota C-HR With a P0014 Code?

No. You should not drive a Toyota C-HR with a P0014 trouble code without first diagnosing it. Neglecting a problem with camshaft timing can cause an engine to fail, which could be expensive and time-consuming.

Many people worry when their vehicle isn’t starting or doesn’t respond. The cause of the problem is what determines the severity.

Major engine damage can result from timing chains that fail. Neglecting to take your vehicle to a mechanic for repairs could cause additional harm and expensive repair bills.

How To Diagnose The P0014 Code In a Toyota C-HR

1. Connect an OBD2 scan tool and search for possible trouble codes. To resolve the P0014 error, you should first diagnose the crankshaft positioning sensor and the camshaft location sensor.
2. Check the engine oil level to ensure it is in good condition. Add oil or replace the filter if it is too low. Clear away any P0014 error code and try again.
3. For signs of sludge, check your service manual or oil filler cap. Your engine oil could be very old, clogging its oil lines to either the variable valve timing or variable camshaft tune (VCT) engine control valve. In these cases, you may need to change both the oil type and clean both parts.
4. Use your diagnostic scanner for testing the variable valve timing or variable camshaft tun (VCT), valve solenoid. Do an output test to check if the VCT-valve solenoid moves. Use 12v+ power and ground to experiment with your car’s electrical system.
5. If possible, remove the variable camshaft tun (VCT), and solenoid control valve and clean oil passages using compressed and suitable cleaning solutions.
6. To verify that they are sending the correct signals, check the crankshaft and camshaft position sensors.
7. Manually check the timing of engine camshafts. Refer to your manual for detailed instructions. If your timing belt or chain is worn, you can disassemble it and inspect the damage.

Toyota C-HR P0014 Code: Common Diagnosing Mistakes

One common error in the Toyota P0014 code is assuming that the timing chain/belt is defective.

Replacements can be expensive and could also be caused by other issues. To ensure accurate results, it is vital to complete a comprehensive diagnosis prior to beginning repairs.

Toyota‘s P0114 signifies a malfunctioning or damaged VVT or VCT system. These systems regulate camshaft timing. There are other possible causes, such as an error in the camshaft position sensor and low oil levels.

How Much Does It Cost To Repair P0014 Code In Toyota C-HR

It costs $195 to repair the P0014 code in Toyota C-HR. Parts cost $95 while labor costs $100.

What Repairs Can Fix The P0014 Code in Toyota C-HR?

• You can add or remove oil from your engine and also change the oil filter.
• Cleaning oil lines that are associated with variable camshaft timing (VCT) and variable valve timing (VVT).
• Clean the solenoid for variable camshaft timing (VCT) and variable valve tuning (VVT), and replace it.
• Repair of the timing belt/chain
• Change the solenoid for the camshaft timing valve solenoid
• Set the Camshaft Position Sensor
• Replace the crankshaft position sensor
• Fix any defective wiring

How To Fix The P0014 Code In Toyota C-HR

• Clearing error codes & performing a road test
• To ensure maximum performance and extended engine life, change the oil and filter with engine-specific viscosity oil.
• Repair or replace wiring to bank 1’s exhaust camshaft oil controller valve.
• Bank 1 will need to change its exhaust camshaft oil regulator valve.
• Follow the instructions in the service manual when replacing the timing chains or camshaft phasers.

In Conclusion

Toyota C-HR’s P0014 code is indicative of a timing problem in the camshaft. This could be caused due to incorrect timing of the camshaft. If this happens, you will be charged a high repair bill.

However, it could also be caused by insufficient oil or a malfunctioning sensor at the camshaft position – both of which can usually be fixed for less than $300.

For assistance, call a skilled mechanic immediately if you are not sure if this problem can be resolved by yourself.